Difference between revisions of "Sludging - Rota sludge"

From Akvopedia
Jump to: navigation, search
(Acknowledgements)
Line 57: Line 57:
 
== Acknowledgements==
 
== Acknowledgements==
 
* The basis for the material on this page was obtained from a desk study shortly to be published on the website of the [http://www.practicafoundation.nl/ Practica Foundation], and from the [http://www.rwsn.ch/ Rural Water Supply Network], and specifically its [http://www.rwsn.ch/prarticle.2005-10-25.9856177177/prarticle.2005-10-26.7220595116/prarticle.2005-11-15.6127855822 manual drilling section].
 
* The basis for the material on this page was obtained from a desk study shortly to be published on the website of the [http://www.practicafoundation.nl/ Practica Foundation], and from the [http://www.rwsn.ch/ Rural Water Supply Network], and specifically its [http://www.rwsn.ch/prarticle.2005-10-25.9856177177/prarticle.2005-10-26.7220595116/prarticle.2005-11-15.6127855822 manual drilling section].
 +
* [http://www.lboro.ac.uk/well/resources/technical-briefs/43-simple-drilling-methods.pdf 43. Simple drilling methods.] WEDC.

Revision as of 23:30, 1 May 2012

Image: 50 pixels This article is under development. You can help Akvopedia by expanding it.

Treadle pump icon.png
Rota sludge in action
Deep drilling with the rota sludge

The Rota Sludge is a manual drilling technique based on the Asian sludge technique, and adapted for harder soil types. To drill through the harder layers, a hardened drill bit and weight have been added. Just after the downward movement of the drill pipes the drill bit is rotated a quarter turn, thus chiselling the bottom of the hole. Water is circulated to bring the cuttings to the surface.

During drilling, the drill pipe is moved up and down. On the down stroke, the impact of the drill bit loosens the soil and on the up stroke, the top of the pipe is closed by hand (or a valve), drawing up the water through the pipe and transporting the cuttings to the surface. On the next down stroke, the hand (or valve) opens the top of the pipe and the water squirts into a pit, in front of the well. In this pit, the cuttings separate from the water and settle out, while the water overflows from the pit back into the well.

The borehole stays open by water pressure. Thickeners such as clay, bentonite or even cow dung are usually added to the water in order to prevent hole collapse and reduce loss of working water (drill fluid).

The Rota-Sludge was developed by the Practica Foundation.

Suitable conditions

Suitable for unconsolidated formations: Sand, silt and clay. Because of the rotation and the drill bit, it is possible to penetrate softer-consolidated formations such as stiff clays, soft sandstone, and weathered laterite.

The Rota Sludge method can be used to drill 2-5 inch wells up to 20 m deep.

Advantages Disadvantages/limitations
- Easy to handle and a temporary casing is normally not needed. It is possible to construct the drilling equipment locally.

- Can drill through softer-consolidated formations.

- The borehole stays open by water pressure. To prevent collapsing, fluid-drilled boreholes must be kept full of water during the entire drilling and well installation process.

- Coarse gravel and other highly permeable materials (cracks in the formation) cause loss of working water and cannot be drilled. If very fine sands (quick sands) are encountered in the first three meter of the borehole, a temporary casing and swell clay are needed on the outside of this casing to prevent collapse.
- If cow dung is used as drilling fluid, this can cause contamination of the well, which can take several weeks to disappear.



Drilling Method Selection.jpg

Construction, operations and maintenance

Diagram of a rota sludge
Drilling a 20 m deep well in Chinandega, Nicaragua, with the Rota-sludge method
Rota sludge drill bit

Cow dung is mixed with water to create a very low cost drilling fluid. It may take several weeks after the drilling is finished for the pathogens (bacteria) to die and disappear completely out of the well.

All drilling equipment is locally produced.

Costs

In India, the cost of a well made with Rota-sludge is about US$ 30. In Nicaragua, this varies from US$ 80 to US$ 400.

The cost of introduction varies between US$ 5,000-20,000 per project, including hand-on training, drill set and drilling of test wells.

Field experiences

The Rota Sludge is used in Nicaragua, Tanzania, Madagascar, Ghana, Senegal, Mauritania and Niger.

Manuals

Reference manuals, videos, and links

Acknowledgements