794
edits
Changes
no edit summary
[[Image:Sand dam flood.JPG|thumb|right|200px|Sand dam during flooding. Photo: [http://www.rainfoundation.org/ RAIN Foundation.]]]
* On impervious bedrock or clay rather than rock with fractures. A good indicator is whether there is some preexisting subsurface flow in the dry season or not and if there are large stones & boulders seen in the riverbed. Extra care should be taken when siting as seepage can occur under the dam in such cases.
* On the base layer rather than on the intermediate clay lens within sand.
* Between defined banks with no old riverbeds on either side which could allow sub-surface water around dam edge.
* दरारों वाली चट्टानों के बजाय अपारगम्य चट्टानों या मिट्टी का चुनाव करना चाहिए. एक अच्छा संकेतक यह देखना है कि सूखे दिनों में पहले से कोई बहाव है या नहीं. यह भी कि नदी तट पर बड़े आकार की चट्टानें और पत्थर आदि हैं या नहीं? ऐसे मामलों में अतिरिक्त सावधानी बरतनी होती है क्योंकि यहां रिसाव की आशंका रहती है.
* ऐसी जगहों का चयन किया जाना चाहिए जहां ढलान बालू को आकर्षित करने वाली हो बजाय कि उसे बहाने वाली. 0.45 मीटर प्रति सेकंड के बहाव वाली नदी में रेत का बहाव कम होता है और यह माना जा सकता है कि ऐसे बहाव वाले इलाकों में बहुत ज्यादा छोटे आकार के कण और गाद आदि नदी तल में हो सकते हैं. सपाट ढलान का अर्थ है चौड़े नदी तट. रेत बांध (सैंडडैम) के लिए इनका आकार 25 मीटर से अधिक चौड़ा नहीं होना चाहिए. आदर्श ढलान 0.125 प्रतिशत से 4 प्रतिशत के बीच होनी चाहिए लेकिन यह इससे अधिक भी हो सकती है. परंतु तब बालू जमा बालू की मात्रा कम होगी. एक आसान परीक्षण यह भी हो सकता है कि एक रेत विश्लेषक की मदद लेकर आकार के वितरण, सांद्रता आदि का परीक्षण किया जाए. मध्यम आकार की बालू को इस लिहाज से सबसे बेहतर माना जा सकता है.
जिन जगहों पर नदी संकरी हो और जहां भूजल प्रवाह पर प्राकृतिक बाधा हो उनका चयन किया जाना चाहिए. ऐसा करने से निर्माण की लागत बहुत कम होती है जबकि बालू अधिकाधिक मात्रा में खुदबखुद मौजूद रहती है.
उन स्थानों का चयन करने से बचा जाना चाहिए जहां हेलाइट (सफेद और गुलाबी चट्टानें) नदी तट की ऊपरी धारा में मौजूद हों. क्योंकि इनकी वजह से पानी में खारापन आ सकता है.
एक ही नदी पर कई बांध बनाने का फायदा यह होता है कि सभी लोग एक ही जल स्रोत का इस्तेमाल नहीं करते हैं और इस तरह क्षेत्र को पर्यावरणीय नुकसान नहीं पहुंचता है. बहरहाल, अगर बांध एक दूसरे से बहुत करीब स्थित हुए तो उनका प्रभाव क्षेत्र एक दूसरे को दरकिनार करना शुरू कर देता है. इससे आमतौर पर जलस्तर में इजाफा देखने को मिलता है लेकिन कुल पानी की मात्रा कम होने लगती है. क्षेत्रवार आधार पर देखा जाए तो मात्रा बहुत मायने रखती है इसलिए बांधों के बीच उचित दूरी रखनी चाहिए. जगह-जगह के आधार पर यह दूरी 350 मीटर से 700 मीटर तक हो सकती है.
ये परिस्थितियां तथा जलवायु, पत्थरों की मौजूदगी या नदी तट की ढाल आदि का विस्तृत विश्लेषण करके ही जगह की सुयोग्यता का निर्धारण किया जा सकता है. इसके अलावा हालांकि इसमें कृत्रिम तौर पर सुधार किया जा सकता है लेकिन पानी की गुणवत्ता कम से कम पीने के लायक तो होनी ही चाहिए.
Site in areas where gradient is suitable to get sand rather than silt. A flow of at least 0.45 m/s river flow means less silt deposition, and such areas will be where there is a suitable gradient – too flat and there will be too many small particles and silt. Flatter gradients also mean wider riverbeds, and for sand dams it should really be limited to 25 metres width. An optimum gradient is said to occur between 0.125% and 4% but can be higher than this but then the sand volume stored is less. An easier field test might be to do a sand analysis to find size distribution, or a porosity & specific yield test from which one can extrapolate the likely sand type. Medium sand will have the best balance between porosity and specific yield, and is therefore the type that is needed.